Back to Raspberry Pi Modules Cameras Accessories

Raspberry Pi Kit X10 Hifi Audio Kit-B X10 DAC Expansion Board + X10-PWR Power Supply Board + X10-I2S Board for Raspberry Pi 3 B

$181.88

97 in stock

Raspberry Pi Kit X10 Hifi Audio Kit-B X10 DAC Expansion Board + X10-PWR Power Supply Board + X10-I2S Board for Raspberry Pi 3 B

Does this kit support Raspberry Pi 4 Model B?

1. This audio kit is designed for pi3 (3B+/3B), and the X10-I2S Board is connected to pi3 by the USB connector. Please refer to the picture shows.
2. This kit will also fit for pi4, but due to the change of pi4 USB port, the USB connector is invalid and you need to use a USB Type A to Type A cable to connect pi4 and X10-I2S Board.
3. In short, if the kit includes a X10-I2S Board and it is use with pi4, you need to prepare a USB Type A to Type A.

[Note]

1. The raspberry pi is not included.
2. Raspberry pi doesn’t support ES9028Q2M(DAC chip, but X10-I2S Board supports this function.
3. Raspberry pi I2S doesn’t support DSD format, but X10-I2S Board supports this function.

[Packing List]

  • 1 x X10-DAC Expansion on Board (with Install Screws)
  • 1 x X10-PWR Power Supply Board (with Install Screws)
  • 1 x X10-I2S Board (with Install Screws)

[For Use With]

– Raspberry Pi 1 Model B+/ 2 Model B / 3 Model B

[Operating System]

– Volumio
– Moode Audio Player

[X10-DAC BOARD]

Features:
– Texas Instruments DAC chipset (PCM1794A) for best sound quality
– 127dB DNR and THD+N: 0.0004%
– 24bit/192kHz Bit to Bit Playback
– TI Ne5534x Low-Noise Operational Amplifiers (Op Amps upgradable)
– Texas Instruments ultra-low-noise voltage regulator
– Dedicated individual DVCC, AVCC power supply
– Selected high quality components (WIMA Film capacitor, Panasonic low ESR aluminum electrolytic capacitor, Gold-plated RCA connectors etc)
– Can connect to our XMOS USB-to-I2S module directly
– Can be used individually with only 4 wires I2S signal connected from other i2s interface
– All dual OPAMP in single dip8 package IC can be used
– High performance and compact Raspberry Pi DAC solution for everyone
Specification:
– Power supply: +5Vdc ±5%, +15Vdc ±5%, -15Vdc ±5%
– Analog audio output level: 2V RMS
– Resolution/Sampling Rate:
  • Up to 24bit / 192KHz (Raspberry Pi I2S)
  • Up to 24bit / 192KHz (Use with XMOS USB to I2S board)
  • DOP64 /DOP28 (Use with XMOS USB to I2S board)
– PCBA Size: 101.5 x 56mm x 34.5mm, PCB size : 85 x 56mm

[X10-PWR POWER SUPPLY BOARD]

Features:
– Fully regulated linear power supply board for X10 / X20 series DAC
– Texas Instruments ultra-low noise TPS7A470x regulator
– Four individual 5.2V/ 5.0V/-15V/+15V to power the Raspberry Pi (1), DAC chipset and OPA
– High performance ELNA and Nichicon Audio Purpose Capacitors
– For use with R-core transformer
Specification:
– Input rating : 6VAC ±5% 2.5A, 6VAC ±5% 0.5A, 15VAC ±5% 0.55A, 15VAC ±5% 0.55A
– Output voltage:5Vdc ±5% 2.5A, 5Vdc ±5% 0.5A, +15Vdc ±5% 0.5A, -15Vdc ±5% 0.5A,
– PCBA size : 85mm x 56mm x 50.5mm, PCB size : 85 x 56mm
Notes:
Low voltage indicator might show up during boot, it does not affect audio performance

[X10-I2S BOARD XMOS USB TO I2S/SPDIF/Coaxial (Optional Accessories)]

Features:
– The XMOS xCORE-AUDIO Hi-Res family of parts
– Deliver precise output with low noise/distortion for soothing, high-quality sound
– Ideal HiFi audio solution for Raspberry Pi
– Streamed through Raspberry Pi to I2S, DSD and/or S/PDIF interfaces
– PCM up to 32bit /384 KHz sample rates (see notes)
– Native DSD, DoP64 and DoP128 (see notes)
– Up to 192 kHz, 16/24 bit resolution S/PDIF output
– Asynchronous Isochronous transfer from Raspberry Pi
– Multiple OS support (Volumio, Moode Audio Player, Windows, Android etc)
– SiTime SiT8208 ultra performance oscillator
– Texas Instruments ultra-low-noise voltage regulator
Specification:
– Power supply: +5Vdc +/-5%
– CODEC: I2S 16, 24, or 32 bit PCM, DSD64 and DSD128
– PCM sample rates : 44.1, 48, 88.2, 96, 176.4, 192, 352.8, 384KHz
– Optional S/PDIF output : Up to 192 KHz; 16/24 bit resolution
– PCBA size : 101.5 x 56mm x 34.5mm, PCB size : 85 x 56mm
Notes:
Not applicable for X10-DAC.
PCM up to 24bit /192 KHz sample rates when works with X10-DAC.

[FAQ & User Manual]

Please refer to WIKI: www.raspberrypiwiki.com/index.php/X10_HiFi

[Hardware Installation]

Note: you need to get a R-core transformer yourself
Or you can buy one online, p lease refer to: X10-RTR Power Supply Unit
IMPORTANT !!!
Connect the R-core transformer to the X10-PWR board
a) Make sure all ports on terminal block are open (Turn clockwise to tighten, counter-clockwise to loosen).
b) Insert wires into the terminal block in the correct order.
C) Tighten down the screws the wires you have inserted. Try pulling each wire out of terminal block in order to insure that they are fastened securely.
White – White : 15VAC 0.55A
Yellow – Yellow : 15VAC 0.55A
Brown – Brown : 6VAC 0.5A
Grey – Grey : 6VAC 2.58A
Power Supply Unit 35W R-CORE transformer:IMPORTANT !!!
AC voltage Selector
110V : AC input voltage MUST be 110~120VAC
220V : AC input voltage MUST be 220~230VAC

a) Make sure that you know what voltage is being supplied by the power outlet before setting the voltage selector switch and before connecting the power cord.
b) To switch the selection, unplug the power cord and use a small screwdriver to slide the switch to the opposite position.

Raspberry Pi Kit X10 Hifi Audio Kit-B X10 DAC Expansion Board + X10-PWR Power Supply Board + X10-I2S Board for Raspberry Pi 3 BBefore pressing the power button:

a) All AC output wires to the X10-PWR board are wired in the correct order.
b) The power cable from X10-PWR board to Raspberry Pi pin header are correctly connected.
c) The AC input voltage selector switch are correctly switched.

[Software Configuration]

Volumio (Version: 2.368)
X10-I2S Not Installed (For X10 Board Kit A)
Select the“PLAYBACK OPTIONS”menu, Turn on “I2S DAC” and select “R-PI DAC” under“DAC Model.” Then reboot and you are done.

Raspberry Pi Kit X10 Hifi Audio Kit-B X10 DAC Expansion Board + X10-PWR Power Supply Board + X10-I2S Board for Raspberry Pi 3 B

Moode Audio Player (Version: 3.1)
X10-I2S Not Installed (For X10 Board Kit A)
Simply select the“Configure”menu, select “Audio” under “configuration settings”, then select “DDDAC1794 NOS” under“I2S audio device”, Then click “SET”and reboot.

Brand Name

Geekworm

Demo Board Type

ARM

Interface

HDMI/RCA Output

Memory Capacity

1GB

Processor Brand

Allwinner

Model Number

Raspberry Pi Kit B

ROM Capacity

None

Intergrated Feature

10/100Mbps

Real customer reviews

There are no reviews yet.
Write a review
X

Like us on Facebook!

Product categories

Shopping cart

×

No products in the cart.